Thursday, June 2, 2011

How long should your brake pads last?

i just had change them about two months ago but i ride every day to work and back then just around my city for fun ... i notice a sqeeky sound just today and it sounded like when i needed brake pads the first time . also they were after market brake pads to, so i dont realy know?How long should your brake pads last?It depends solely on how much you use the brakes. Check the thickness of the pad. I've had aftermarket get noisy long before time to change.How long should your brake pads last?if you buy OEM, then about 30k miles is the average. If you buy cheap pads, then about 15k if thatHow long should your brake pads last?when you buy the break pads ask them how long there good for, aask how many miles and it depends on how good of a driver you are if you dont ride the breaks etc, stopping turning raduiis in other words, whenever they sel you damn good break pads too hons!!How long should your brake pads last?When your brake pads wear down, they're going to leave a lot of brake dust. The brake dust can cause your brakes to squeak. Remove the brake pads/shoes and clean them with %26quot;contact/brake%26quot; cleaner (can get it at any bike or auto parts store). Clean the disc/drum also. If the brakes pads/shoes are glazed (shinny) scuff them up with a wire brush and clean again.



WHENEVER you do work on your brakes (remove a wheel, change brakes, adjust, bleed) make sure they work.

-If hydrolic, pump the lever/pedal to fully seat the brakes.

-When you first start off, lightly apply the brakes and let them drag while you're riding, to get the pads/shoes to match the disc/drum.

-When the brakes are strong enough to lock up the F or R wheel in a panic stop, then your brakes are ready and you're good to go.How long should your brake pads last?Brake pads have wear indicators that squeal loudly when your pads wear down.This is to let you know when its time to change them.Just listen for the noise they will tell you its time.How long should your brake pads last?I've had my OEM pads for 26K miles, but I need new ones!

I think i need a brake change please help.?

Just recently my car brakes started to squeak. Ive had those brakes for about a year and six months. I dont know if the brakes have dust in them, i dont know. It only squeaks when i slightly press the brake, when i press it all the way its all good. If i do need this brake change how difficult is it to do it your self, i have never changed brakes my self, but i did rebuild a top end of a AMC and made it run again. I have front disk brakes and drums in the back. what kind of brake pads should i get, cause iam getting them from auto zone, and the prices very bettween diffrent brands, $35 is the most ill pay for a pair of brake pads. so which ones should i get, what do i need to keep in mind. thank you for all your helpI think i need a brake change please help.?OK it sounds like it's about time, dust is a factor but after 20 months it's time. %26quot;Bendix or Raybestes%26quot; are your best bet and you may get another 16 to 20 months. With the rotors and drums if you run a finger nail across the surface and it gets caught or really feels rough they need to be turned, turning the drums and rotors will make the brake shoes and pads last longer. Yes get the %26quot;Auto Repair Manual%26quot; for your car to help you with the job the first time or 2. Good Luck and take it slow the first time or 2.I think i need a brake change please help.?mate. there's usually inspection slots in the caliber so go look at the pad thickness.I think i need a brake change please help.?get Bendix brand,, the best is the only way to go with your brakes. I get mine from Advance Auto.I think i need a brake change please help.?You get what you pay for, get the cheap ones and they blow out black dust and squeal like a retarded pig..... get the better pads, ceramic are the best. They are easy to change, you will need to buy a C-clamp to push the piston back in the caliper for the disc brakes.I think i need a brake change please help.?You do not know what the problem is and do not know how to do it. Yet you want to fix it your self for $35. I am glad I do not live in Long Beach.

Hey: We mechanic need to make a living too.I think i need a brake change please help.?Well for starters you get what you pay for. Pads will range anywhere from 6.00 to 60.00. They have the regular elcheapo and then they have extreme duty. You asked a question that leaves a lot of questions open. You need to go somewhere and get a free brake check. There are a number of things that could be making the pads squeak besides actually needing to replace them. You mentioned dust that is one thing. Stuck caliper will give that effect also. Dry slides. Broken anti squeaker. I have even had a bad hose cause that effect. How old is the car.I think i need a brake change please help.?Yeah, you can do it ,but you might want to buy a Haynes repair manual for your car. It will tell you what, if any ,special tools you will need.

Get the middle priced set of pads and be sure to apply the anti squeal paste or the plastic shims that come with them.

DON'T use a bumper jack or the jack that came with your car unless you place it on stands . Be safe, don't get under ANY car if it's not on stands.I think i need a brake change please help.?It depends, how hard are you on your breaks? If you ease into everything, they may just be glazed over. If this is the problem, a spin on a grinding wheel should do the trick. As for difficulty, disc breaks are easier to change and drums are a little more complicated.I think i need a brake change please help.?get semi -metallic pads and shoes about 20.00 ea set The sound you hear by that description is that of the early warning device on the pads to tell you that the pads are ready to be changed-- its a piece of metal that makes a noise because it touches the rotor first when the pads are worn. as for the work it is fair but the trick is that you need some specialty tools ie brake spring pliers, brake spoon, hex or torques wrench/socket 6%26quot; c-clamp and you have to run the rotors and drums down some where to get them cut in the back take both drums off but only change one set of shoes at a time so you can look at the other side if you get lost If you have abs most of them dont like having the fluid pushed back into the master cylinder so you have to clamp the line open the bleeder screw to push the caliper back if you do it yourself get a book hope this helps

How do you know when a brake rotor is bad? How do you know when they need to be turned?

I've looked everywhere for answers to these questions. I've just changed my brake pads but am unsure how brake rotors are supposed to look or feel. What does turning them do? If a rotor isn't perfectly smooth, what effect does it have on your brakes? Thanks.How do you know when a brake rotor is bad? How do you know when they need to be turned?get rid of that Toyota van already, Ray!!! do you see many of these on the road? there's a reason why not......How do you know when a brake rotor is bad? How do you know when they need to be turned?Rotors over time wear thinner in thickness..... for each make/model there is a minimum thickness of the rotor before it is deemed unusable or unsafe..



if the rotor isn;t perfectly smooth it will wear the brake pads abnormally or faster sicne it has to grind itself down to fit the grooves of the rotorHow do you know when a brake rotor is bad? How do you know when they need to be turned?If the rotor needs turned you will feel a vibration while braking.

They are usually stamped with the minimum thickness that they should be turned to near the wheel stud area.

I personally never turn them, and just buy new ones because the new rotors usually cost only a few more dollars than the cost to turn the old ones.How do you know when a brake rotor is bad? How do you know when they need to be turned?the rotors should be turned everytime the brakes are replaced so the pads break in evenly and you get full pad upon brakeing, the symptions of a bad or warped rotor is a pulsating feeling in the brake pedal when applying the brakes.How do you know when a brake rotor is bad? How do you know when they need to be turned?Typically a bad rotor will either be warped (high bumps in random places) or wavy (high and low spots radiating out from the center). You can use a straight edge to see how straight the rotor is in various areas to get an idea if its ok or not. But honestly with the low price of imported rotors at most parts stores, virtually no one turns rotors anymore. My friend who runs his own shop sold off his rotor resurfacer several years ago, you can't charge customers 15 bucks a rotor to turn them when new ones are 25, so you don't waste your time you just sell them the new rotor and make your money marking those up and installing them.How do you know when a brake rotor is bad? How do you know when they need to be turned?If your steering wheel shakes when you apply the brakes you should have them turned. If you noticed that the rotors looked as if they had grooves worn around them, you should have them turned. If you had hot spots or discoloration, it wouldn't hurt to have them turned. If you've had them turned more than once or twice and a lot of material was removed then you should consider having them replaced. The guy turning them should be able to put a set of mics on them and tell you if they are getting too thin to turn again.How do you know when a brake rotor is bad? How do you know when they need to be turned?i own a shop and you can look at them and see if the have grooves cut in them or odd markings on them that shouldn't be there,they should look smooth,you can also tell this by if they wobble when you put your foot on the brake pedal also,if you feel it go up and down a lot this means their warped,most of the time you can just remove the wheel and rotate the rotor a little and see if it wobbles or has deep grooves in it,if you see any of this you either need to get these turned or get new ones for it,good luck with it,i hope this helps.How do you know when a brake rotor is bad? How do you know when they need to be turned?a brake rotor has a musurement on each car,most of the time marked on the inside of the rotor.if you put pads on its a good idea to have thrm turned.reason is there can be high and low spots on the surface and this can cause the brakes to shakeor make the car jerk when applied.most rotors get damaged by the driving habits of the driver,if you drive fast and hit your brakes to make a quik stop,that causes the rotors to get the high spots in them.also riding the brake will cause this.if you drive regular and not alot of stopping involved,you wont have to cut the rotors too much.just enought to get the layer off the surface of the rotor from build up.How do you know when a brake rotor is bad? How do you know when they need to be turned?a good brake shop will take a micrometer that measures thickness and measure each rotor,then compare results to the measurements that is stamped on each rotor/hub if within limits they usually turn them and that provides a smooth surface for the brake pads -----with a un-even surface or a ridged surfaced that will cause the pads to be ridged or not wear evenlyHow do you know when a brake rotor is bad? How do you know when they need to be turned?the rotors make a squeeking noise and when you stop you kind of have a buzzing sound and it will harm your brakes life and its better that you change them as soon as possibly because the brake life will go out and it will get ruinedHow do you know when a brake rotor is bad? How do you know when they need to be turned?Your rotors can be spot checked with this trick. If you can not write a smooth line across the surface of the rotor with a regular ball-point pen; it needs to be turned if it has enough thickness to be machined. What I mean is to try to write your signature in several places on the %26quot;cleaned%26quot; rotor, without any blank spots or skipping, if you can; the rotors are smooth enough for good pad contact.



This only works on solid faced rotors; this is Yahoo Answers after all.How do you know when a brake rotor is bad? How do you know when they need to be turned?the rotors should be turned every time you replace the brake pads. they should be as smooth as a babys butt on the surface that they touch the brake pads. rotors can only be turned down to a safe minimum thickness which is measured in hundredths of an inch. take them to your local parts store to have them measured and possibly turned. if you dont have them turned, the uneven ness (sp) and grooves take away from the total surface area that your brake pads touch them and your brakes will overheat. the excessive friction on the smaller surface area creates intense heat. the pads and the rotors should mate up together nice and smooth. if you dont turn them and the heat builds up the rotors will warp, or become out of round laterally causing a pulsating feeling in the brake pedal.How do you know when a brake rotor is bad? How do you know when they need to be turned?when your rotors are bad,you will get a pulsation in your brakes,and when you get the rotors turned,you should get even braking action,without pulsations.
  • i can't find my scan
  • can i play wow check my laptop
  • How do I know it's time to have the fluids flushed in my car?

    I have a 2002 Honda Accord V6 with approximately 149,000 miles. I had my car in the shop today for an oil change. Mechanic just called and said he had some %26quot;recommendations.%26quot; He said it needed brake and transmission fluids flushed for $225 and the fanbelts replaced for $125. I already had the timing belt replaced at 100,000 miles so I already know that doesn't need to be done (that cost me over $400 from a different mechanic). Anyway, I have a friend that says he can do all of this for me. I worry that he might not do it right, but I don't want to offend him. Don't you need special equipment to flush the fluids? I'm no mechanic and neither is my friend, so I'm just wondering if it's possible. I mean you don't have to be a mechanic or have special equipment to change your oil... so I guess it's possible to do these other things too. Can someone let me know?How do I know it's time to have the fluids flushed in my car?There are a couple of considerations - maybe the mechanic your seeing now is trying to make a $ out of you or maybe the mechanic you saw last didnt actually do the work - we have a mechanics business and I cant tell you how many times people have told us that something was done recently and it just wasnt done at all.



    Brake fluid does need a specific tool to drain out and you need to know how to bleed the brakes after the refill or your brakes wont work properly



    Transmission fluid - to be honest Im not sure (Im not a mechanic I work in the office) we top up transmission fluids but we dont replace it - we send transmission jobs to transmission specialists for a transmission service so Im sorry I cant really help you there.



    As for your friend - if he knows what he is doing there shouldnt be a problem for him just make sure especially with the brake fluid that he knows how to bleed the brakes or dont let him do it.



    ...



    You dont need special equipment to change the fan belt but it must be put on correctly - does your users manual have a map of how the fan belt goes on? Each car is different we have spent a few hundred dollars just buying software that shows us how each one goes on each car (along with timing belts etc)



    OH I had another thought also - if he is changing all these fluids he is on his way to doing a service so you should probably get him to change the air filter, the oil filter and the fuel filter while he is at it - also the radiator is really easy to flush and replace the water and coolant - if you have a friend who is willing to do all this for you it might be worth investing in a workshop manual for your car you can get these through most auto parts shops.

    Help with my survey on maintaining cars for my school project?

    1. Do you know how to maintain your own car? Yes/No

    2. Do you do your own maintenance? Yes/No

    3. Do you do your own tune up? Yes/No

    4. Do you know how to check tire pressure? Yes/No

    5. Do you have the tools to do your own maintenance? Yes/No

    6. Do you take your car to shops for maintenance? Yes/No

    7. Can you change your air filter? Yes/No

    8. Can you change the engine oil? Yes/No

    9. Can you change belts? Yes/No

    10. Can you change brakes? Yes/No

    11. Do you know where to dispose used oil and filter? Yes/No

    12. Do you know how to change coolant? Yes/No

    13. Do you know how to jump start your car? Yes/No

    14. Do you know how to change tires? Yes/No

    15. Do you know how to use a jack? Yes/No



    will u please answer these questions

    just type yes or no for each one

    thank youHelp with my survey on maintaining cars for my school project?Yes to all.



    Note on #6 I take the car to the shop, because a lot of jobs are easier to do on the lift, but I do the work myself.Help with my survey on maintaining cars for my school project?y

    y

    y

    y

    y

    n

    y

    y

    y

    y

    y

    y

    y

    yHelp with my survey on maintaining cars for my school project?yes

    yes

    no

    yes

    yes

    yes

    yes

    yes

    yes

    yes

    yes

    yes

    yes

    yes

    yes

    yesHelp with my survey on maintaining cars for my school project?1. Yes

    2. Yes

    3. Yes

    4. Yes

    5. Yes

    6. Yes

    7. Yes

    8. Yes

    9. Yes

    10. Yes

    11. Yes

    12. Yes

    13. Yes

    14. Yes

    15. YesHelp with my survey on maintaining cars for my school project?Yes to all answers except #6. I don't take my vehicles to any shop for maintenance, just major repairs.Help with my survey on maintaining cars for my school project?Yes to all except number 6. I'm a mechanic so I do all the work (minor and major) to my car myself.

    How do you know what model number disk brake your bike has?

    I want to change the pads on the disk brake on my bike, but can't find the model number. All I know is that it is a Promax disk brake.How do you know what model number disk brake your bike has?Go to the Promax web site and match the pads.



    http://www.promax.com.tw/How do you know what model number disk brake your bike has?Go to the shop where you bought the bike and let them exchange the pads, it is not simple and if you do it wrong it is unsafe.

    How to fix your brake lights?

    I have changed the bulbs on my brake lights but they are still not working, what could be the problem with them and how do you fix it?How to fix your brake lights?I had a similar problem when my trailer blew out a fuse for my brake lights. Check the fuse, it might be burned out. If that's not the problem, then the switch under the brake pedal (the one that turns on the brake lights) might be faulty. If that is not a cure, then best to go see a mechanic.